Gel Press Tutorial: Visible Image

Hello everyone and lovely to see you here…

I’m back today with a tutorial for Visible Image showing you how I made the Gel Press cards I recently posted on the Visible Image Facebook page and I was going to attempt a video but honestly, no one needs to hear me wittering on and I am utterly inept when it comes to technology!

These were the two cards I shared on the Facebook page…

… and I had such a good response and there was a hearty ‘yes please’ to my tutorial offer so I hope this helps in some way.

This is the card I’m going to make with you today and take you through the process step-by-step.  It really is very simple and fairly quick to make.

These are the main tools I used for the make… a 6″ round Gel Press, the Into the Woods stamp set, masking tape, a small brayer, a water spritzer and some watercolour card which I trimmed into a 7″ square.  The Gel Press is brilliant.  Made from a rubbery gel, it holds mediums on the surface and allows you to press stencils or stamps (or anything  – leaves, end of tubes, corrugated card, bubble wrap) into the medium and create mono prints which you can then use alone or add more images or text too.

Stampers Grove have an amazing selection of Gel Press plates in various sizes and shapes so if you’d like to experiment with one, why not buy a small one to see how you get on?  There are hundreds of YouTube videos explaining different techniques and they’re hugely inspiring.

The first step in making your circle is choosing your medium and I used Distress Oxide ink pads but you could also use Distress ink pads or Distress Spray Stain or Distress Oxide Sprays… the choice is unlimited and each different medium will give you a different looking effect.

Firstly dab the ink pad around the gel press to build up colour but try not to contaminate each colour by over laying on the other.  You can see where I’ve dabbed the ink onto the gel press and then how the oxide ink almost ‘comes to life’ when I’ve spritzed with water.  Also, give the watercolour card a very light spritz as this helps the colours bleed into each other and creates a watercolour effect.  Next, lay the card onto the gel press, smoothing it down gently.

Distress Oxide ink pad colours used:

        • Black soot
        • Hickory Smoke
        • Chipped Sapphire
        • Faded Jeans
        • Stormy Sky
        • Dusty Concord

It’s hard to see but on the first photograph here I had quite a lot of water pooled around the black area so I just grabbed some kitchen roll and soaked it up by using a corner of the paper towel to slurp up the excess.  After slightly drying, I spritzed the card very lightly with water and overlaid another piece of paper towel.  This takes the colour away where the water drops have been and you get a lovely texture in the background.  I’ve then sprayed on some Glimmer Mist in a pale gold colour but you can leave this out if you’d like a ‘cleaner’ card.

Once dry, overlay a sheet of scrap paper and draw round the circle.  Trim the circle out and  tape the sheet over the watercolour card so any stamped images that go over the circle won’t print onto the card itself.

For the background tree stamp, I used the Distress Oxide Hickory Smoke ink pad and you can see where the excess has stamped onto the scrap paper we taped down.

The foreground trees and the beautiful lone standing tree are both stamped using Onyx Black from Versafine and I’ve stamped both going off the edges so that there are no edges stamped not to he finished card.

Stamp the sentiment from the set however you choose (so many ways to play with those words!) and then remove the scrap sheet from around the card.

I’ve then taken the little star stamps from the Faerie Magic set and stamped them using Weathered Wood (Distress Oxide) just around the sentiment to add extra interest but you could add a few small adhesive gems or sequins in a co-ordinating colour.

To finish, I matted the card onto a navy blue card stock and then onto an 8×8″ card blank which I then trimmed to size… and that, as they say is that!

I went on to make this card as I made a few backgrounds while I had the Gel press out and I’ve used the Night Owl set for this make, heat embossing the owl to add a different texture.

The Gel Press or Gelli Plate (two different makes of the same product) is a lovely way of working.  You can never be sure what’s going to appear when you peel that paper off and I love that!

If you have a go at this, please upload a photo onto the Visible Image page as I’d love to see them.

Thanks for reading everyone… catch up again soon.

H xx

2 thoughts on “Gel Press Tutorial: Visible Image

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.